Blue Rhino GWU501E Manuel du propriétaire télécharger pdf (Page 6)

Outdoor Patio Heater Model No. GWU501E Contact 1.800.762.1142 for assistance. Do not return to place of purchase.

page no.

Lighting

Note: this heater is equipped with a pilot light that

allows for safer startups and shutdowns. Pilot must

be lit before main burner can be started.

1. Turn tank valve OFF.

2. Push control knob in and turn to OFF.

3. Wait 5 minutes for any gas to clear.

4. Turn tank valve ON.

5. Open viewing hole by sliding cover to either side.

6. Push control knob in and rotate to pilot position.

Note: for initial start or after any tank change, hold

control knob in for 2 minutes to purge air from gas

lines before proceeding.

7. Push igniter button once. Pilot light flame will

appear and be visible through viewing hole.

8. Release control knob after 30 seconds. Pilot light

will remain lit. If not, return to step 1.

9. Turn control knob to HIGH. Main burner will light

immediately. Flame is visible through viewing hole.

If not, return to step 1.

10. If for some reason your ignitor fails to deliver a spark, your heater can be started by

inserting a lit match through the pilot view hole while pushing the control knob in while

in the pilot position.

Have a question or are having problems visit www.bluerhino.com or call 1.800.762.1142.

Note: the burner may be noisy when initially turned on. To eliminate excessive noise from

the burner, turn the control knob to the pilot position. Then, turn the knob to the level of

heat desired.

When heater is ON:

Emitter screen will become bright red due to intense

heat. The color is more visible at night.

Burner will display tongues of blue and yellow flame.

These flames should not be yellow or produce thick

black smoke, indicating an obstruction of airflow

through the burners. The flame should be blue with

straight yellow tops.

If excessive yellow flame is detected, turn off heater

and visit www.bluerhino.com or call 1.800.762.1142.

Re-lighting

Note: For your safety, control knob cannot be turned OFF without first depressing control

knob in PILOT position and then rotating it to OFF.

1. Turn control knob to OFF.

2. Wait at least 5 minutes, to let gas dissipate, before attempting to relight pilot.

3. Repeat the “Lighting” steps.

Shut Down

1. Turn control knob clockwise to pilot. (Normally, burner will make a slight popping sound

when extinguished.) Burner will extinguish but pilot will remain ON.

2. To extinguish pilot, depress control knob and continue to turn it clockwise to OFF.

3. Turn tank kalve clockwise to OFF and disconnect regulator when heater is not in use.

Note: After use, some discoloration of the emitter screen is normal.

Operating Instructions

Inspect the visible portion of the hose before each use of the appliance. Inspect the entire hose

assembly at least annually.

Checking for Leaks

Burner Connections

Make sure the regulator valve and hose connections are securely fastened to the

burner and the tank.

If your unit was assembled for you, visually check the connection between the burner

pipe and orice. Make sure the burner pipe ts over the orice.

WARNING: Failure to inspect this connection or follow these

instructions could cause a re or an explosion which can cause

death, serious bodily injury, or damage to property.

If the burner pipe does not rest ush to the orice, please contact 1.800.762.1142 for

assistance.

Tank/Gas Line Connection

Make 2-3 oz. of leak solution

by mixing one part liquid

dishwashing soap with three

parts water.

Make sure control knobs are off.

Turn LP gas tank ON at valve.

Spoon leak check solution at all

indicated locations

If any bubbles appear turn LP

gas tank OFF, reconnect and

re-test. If you continue to see

bubbles after several attempts,

disconnect LP gas source and

contact 1.800.762.1142 for

assistance.

If no bubbles appear after one

minute turn tank OFF, wipe away

solution and proceed.

Before Lighting

Heater should be thoroughly inspected

before each use, and by a qualified

service person at least annually.

If relighting a hot heater, always wait at

least 5 minutes.

Inspect the hose assembly for evidence of excessive abrasion, cuts, or wear. Suspected areas

should be leak tested. If the hose leaks, it must be replaced prior to operation. Only use the

replacement hose assembly specified by manufacturer.

OFF

LOW

Pilot

(Push in)

HIGH

Pilot

(Push in)

HIGH

LOW

OFF

1 2 3 4 5 6 7 8 9

Commentaires sur ces manuels

Pas de commentaire

Blue Rhino GWU501E Manuel du propriétaire Page 6

Commentaires sur ces manuels

Produits connexes et manuels pour Chauffages d'appoint Blue Rhino GWU501E